I just received your plant protector pack. I see that they are much smaller than I imagined. When reading your original post online before I purchased, it said that one package will be good for an entire cycle for 90 indoor or 20 outdoor plants. I have 120 indoor. While reading the directions I don’t know how to use it. Am I supposed to only put one bottle cap into 1 quart of water for all 120 plants, and foliage feed them? That wouldn’t be enough. I usually have to use about 2 gallons of water when I foliage feed them. (I use one of those pump most sprays that you can spray pesticides with). Or do I need to calculate how many bottle caps I need for 2 gallons? Meaning I would need to use 2 of your mold control bottles for only one time of use. That doesn’t sound right. I would also like to know the exact directions for the bug blaster and root protector too. Please reply with exact directions when you get a chance. Like do I poor the root protector with the Res? Do I foliage feed the bug blaster? Can I mix bug blaster and mold control into one foliage feeding batch? I usually use about 20 gallons to water everyday. I’m about to be in the 5th week of flower. Each plant is huge, they were about 3-4ft tall before I flipped into flower. They haven’t really grown much since then, and the flowers haven’t been biding good because I read that I can use organic apple cider vinegar and water to get rid of powers mildew. It said to use two tsp quart. So I used 16 tsp in 2 gallons of water while waiting for your package, and it made a few plants completely droop and get wilted. Since that happened the buds haven’t really grown in size, but that was over a week ago, and now they are bouncing back slowly. I just don’t want to ruin anything by doing this wrong too. Please advise. Thank you for your time
You should probably any be using roughly 8 tsp per 2 gallons start off light. You’ll usually start off with,half of the recommended dose some times lower. Foliar feeding is a good fast way for plants to uptake nutrients and it will work to Foliar feed with as well
So do I use only 1 bottle cap (5ml=1 tsp) into one quart of water for all 120 indoor plants? I usually use 2 gallons when dollar feeding. I have this big pump pesticides sprayer. Do I need a diff mister and only put one tsp into 1 quart? Or do I use two whole bottle of the mold control for the one time use into 2 gallons? That doesn’t seem right bcuz the add said one bottle of mold control is good for 1 entire cycle for 90 indoor plants. Also, how do I use the root protector? Can u give exact directions? Like, do I mix it with the Res water along with the nutrients? Or do I make a diff Res for the root protector alone, and how much of it do I use? Also, bug blaster?
No I’m asking about all three. How do I use mold control? I read directions but it’s such a small bottle, I would need two full bottles in my 2gallon foiliar feeding sprayer, and that doesn’t sound right. Am I supposed to use two bottle of mold control for my 2gallon sprayer or do I need to only use one quart of water and 1/4th of the mold control bottle for all 120 plants, like it says in directions? Am I using a bad sprayer? Do I need a better mister so that 1 quart will be enough for all 120 plants?
Dissolve one bottle cap of Bug Blaster in a quarter gallon of water (1 liter). Spray the plants from top to bottom with the solution, paying extra attention to the bottom of the leaves where spider mites, thrips and other pests reside. Use a plant sprayer with a very fine mist. For the best results, use at the beginning of the dark period. Repeat after five days.
One bottle of Bug Blaster is enough for 20 large outdoor plants, or 50 indoor plants. Use a double dose for heavy infestations.
How to use Root Protector
Dissolve one bottle cap of Root Protector in a quarter gallon of water (1 liter). Divide the solution evenly amongst the plants. Afterward rinse with plain water to spread the solution though the roots.
For the best results, use at the beginning of the light period. One bottle of Root Protector is enough for 20 large outdoor plants or 50 indoor plants. . Use a double dose for heavy infestations.
How to use Mold Control
Dissolve one bottle cap of Mold Control in a quarter gallon of water (1 liter). Spray the plants from top to bottom with the solution, paying extra attention to the bottom of the leaves. Use a plant sprayer with a very fine mist.
For the best results use at the beginning of the dark period. One bottle of Mold Control is enough for 20 large outdoor plants or 50 indoor plants. Use a double dose for heavy infestations.
Anita, when you reply be email, make sure it doesn’t have your email address or other info listed. You will need to come onto the forum and edit your response and remove your email address. I will flag it as well so that it is removed, in case you aren’t available.