Yes could ya please post the list
1 Like
Oh I have stuff you can do LOL… chopping firewood is high on the list LOL
6 Likes
That is absolutely beautiful 
2 Likes
Yes: -40 soak for 4 hours separate then combined and shaken every minute for ten minutes. The leftover material is used for full spectrum extract.
4 Likes
You should read those articles and/or view the youtube videos ichiban has for sure. But @Myfriendis410 has you covered. I plan on following his method for dababble oil.
See parts list below:
DIY Vacuum Still Component List
This is a loose list of components for the DIY Vacuum Still project. Some I have used and some
I have not personally used but think they look appropriate.
ANYONE USING THIS INFORMATION TO PURCHASE AND USE ANY EQUIPMENT
MENTIONED HERE DOES SO AT THEIR OWN RISK AND IS RESPONSIBLE FOR
CONFIRMING THE SAFETY OF ANY EQUIPMENT PURCHASED OR USED.
FOR BVV PURCHASES: please contact Nina Black directly at NinaB@shopbvv.com
She is familiar with the lids and other pieces I’ve been working with.
Main Components
Heat source (HS)
Loading vessel (LV)
Loading vacuum lid (LVL)
Transfer tubing
Condenser (C)
Reclaim vacuum lid (RVL)
Reclaim vessel (RV)
Cooling pan for reclaim vessel (CP)
Vacuum Pump (VP)
Heat Source (HS)
I think almost anything that is safe and NOT an open flame can work. One from a garage sale or
from a friend can keep the budget lower. I like the IH because of safety and the low profile but
they add expense and the LV used with it must be IH compatible.
Elite Gourmet ESB-301BF
(https://www.amazon.com/gp/product/B00C8C5I7I/ref=ppx_yo_dt_b_asin_title_o06_s01?ie=U
TF8&psc=1)
$20.99
Duxtop Portable Induction Cooktop, Countertop Burner Induction Hot Plate with LCD Sensor
Touch 1800 Watts, Black 9610LS BT-200DZ
https://www.amazon.com/gp/product/B07KSNTSVR/ref=ppx_yo_dt_b_asin_title_o05_s00?ie=
UTF8&psc=1
$119.99Loading vessel (LV)
Pots from the cupboard will work fine. Non-stick surfaces work the best. The most important
consideration here is that the LV fits to the middle of the seating area of the LVL seal. Below
are just the ones I tried and worked. There are tons of options for this piece.
Stainless Steel can work with the addition of boiling beads. The combination of IH tech,
stainless, and boiling beads can work at a pretty fast rate.
2.5-Quart to Match with the 8” glass LVL
Stainless IH compatible (buy boiling beads separately)
Duxtop Professional Stainless Steel Sauce Pan with Lid, Kitchen Cookware, Induction Pot with
Impact-bonded Base Technology, 2.5 Quart
https://www.amazon.com/gp/product/B00GBVSV76/ref=ppx_yo_dt_b_asin_title_o04_s00?ie=U
TF8&psc=1
$45.99
6-Quart to Match with the 10.75” glass LVL
Cuisinart 644-24 Chef’s Classic Nonstick Hard Anodized 6-Quart 6 Qt Stockpot, Black/Stainless
Steel
https://www.amazon.com/gp/product/B0001LO5H2/ref=ppx_yo_dt_b_asin_title_o02_s02?ie=U
TF8&psc=1
8-Quart to Match with the 11.25” glass LVL
KitchenAid Hard Anodized Induction Nonstick Stock Pot/Stockpot with Lid, 8 Quart,
Matte Black
https://www.amazon.com/gp/product/B08GDYQ4SB/ref=ppx_yo_dt_b_asin_title_o09_s00?ie=
UTF8&psc=1
$85.49
Loading vessel lid (LVL)
These are custom assemblies from BBV so they are not available on the website (right now
anyway). You will need to speak with BVV directly.
8" (it is actually 8.375”) Diameter GLASS LID w/ 2 port hardware
$80.0010.75" Diameter GLASS LID w/ 2 port hardware
$96.00
11.25" Diameter GLASS LID w/ 2 port hardware
$98.00
Transfer tubing
FOR COMING OFF THE LV:
These are very stout tubing and won’t bend at quick angles so plan lengths and
setup accordingly. The “Tubing 90-degree splicer 3/8 to 3/8” recommended in the
“additional equipment” section below can help with this.
Silicone Tubing (peroxide cured)
3/8 ID 3/4 OD
SKU: LS-PST-38
$3.85 per ft. (10 ft. min. order)
https://labsociety.com/lab-equipment/peroxide-cured-silicone-tubing/
Dura-Pure PVC
3/8″ ID x 100′,
PVCBH38-594ANA
(this is 100’ so if you can find the same elsewhere in shorter length can save money)
https://www.atp4pneumatics.com/product/pvcbh38-594ana/
This tubing is not as stout so please read the important note below.
Tygon 3/8 ID
Tygon 2475 Smooth Bore High Purity PVC Tubing - 3/8"
SKU: ACG00027-5
$18/5ft
Important note: I’ve used this tubing a lot without problem coming off the LV and other
connections without issue for a while. However, I am at 5,000’ elevation so I don’t have
a problem with it. If using at sea level and running hotter temp it may be a problem and
one of the more stout options above will work better for you…
Tygon 2475 Smooth Bore High Purity PVC Tubing - 3/8"
(Alternate: 3/8" ID x 1/2" OD x 1/16" Wall Tygon® 2475 High-Purity Tubing | U.S. Plastic Corp.)
FOR OTHER CONNECTIONS:
Tygon 2475 Smooth Bore High Purity PVC Tubing - 1/4"
SKU: ACG00017-5
$14.00/5ft
Tygon 2475 Smooth Bore High Purity PVC Tubing - 1/4"(Alternate: 1/4" ID x 3/8" OD x 1/16" Wall Tygon® 2475 High-Purity Tubing | U.S. Plastic Corp.)
Tygon 3/8 ID
Tygon 2475 Smooth Bore High Purity PVC Tubing - 3/8"
SKU: ACG00027-5
$18/5ft
Important note: I’ve used this tubing a lot without problem coming off the LV and other
connections without issue for a while. However, I am at 5,000’ elevation so I don’t have
a problem with it. If using at sea level and running hotter temp it may be a problem and
one of the more stout options above will work better for you…
Tygon 2475 Smooth Bore High Purity PVC Tubing - 3/8"
(Alternate: 3/8" ID x 1/2" OD x 1/16" Wall Tygon® 2475 High-Purity Tubing | U.S. Plastic Corp.)
** Make sure to consider where connectors and hose clamps will be necessary
Condenser (C)
Build your own option: Most cost effective to start with
- uses a cooler you already have or a cheap styrofoam one.
- fill with ice bath or combination ice bath with dry ice assist.
- submerge coil/tubing in ice bath for cooling.
Stainless Options:
Stainless Coil from Amazon
(I’ve used this and works as expected with good price point)
MAKE SURE TO WASH OUT WELL
https://www.amazon.com/Jockey-8-inch-Stainless-SteelTubing/dp/B00WQAV21I/ref=rvi_sccl_4/143-0139267-
3426272?pd_rd_w=HSHl0&pf_rd_p=f5690a4d-f2bb-45d9-9d1b-
736fee412437&pf_rd_r=Y9V152YCYSHBFY2KST8K&pd_rd_r=30ae902d-9003-4dc4-
a942-7a33c510fa1d&pd_rd_wg=QhyhD&pd_rd_i=B00WQAV21I&psc=1
99$
Square Jockey Box Coil - 70’ - Stainless Steel - High Efficiency
(I’ve never used this but it looks like a good option at good price)
https://www.kegworks.com/jockey-box-coil-70-squarekit/?country=US¤cy=USD&keyword=&matchtype=&device=c&adtype=&produc
tgroup=976926012156&productidSquareCoil70Kit&utm_term=&utm_campaign=(ROI)
+Smart+Shopping±+Draft+Beer&utm_source=adwords&utm_medium=Tubing Options:
Use 20-50 feet of any 3/8” ID tubing from the transfer tubing list.
I think the thinner walled Tygon tubing should work better than the thicker walled tubing
but I haven’t concentrated on testing the differences.
Pre-fab option. Expensive but useful.
Stainless Steel Injection Coil
Flare Size: 3/8-inch
SKU: IJC800-06
$365
Stainless Steel Injection Coil
*pay attention to the hardware on this. You may want hose barbs to attach tubing.
Reclaim vacuum lid (RVL) & Reclaim vessel (RV)
2 Gallon Resin Trap Vacuum Chamber
SKU: BVV2G-RT
$135.00
2 Gallon Resin Trap Vacuum Chamber
**Need barbed 1/4" port for the port going to the pump
Cooling pan for reclaim vessel (CP)
Anything that is shallow, water tight and large enough for the RV to set in.
Vacuum Pump (VP)
DIAPHRAGM PUMPS
The main requirement is looking for an ultimate vac level of 50 mbar or better. The speed isn’t
really important but they will be around 24 to 30 L/min.
24L Lab Diaphragm Vacuum Pump Oil Free
Amazon
$139.00
https://www.amazon.com/gp/product/B085FPPMMR/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=
UTF8&psc=1
** The manufacturer has said that this pump is not safe to work with ethanol vapor. Many
people are using it with ethanol but it looks like it could have a safety issue.OIL PUMPS
Any 3cfm or bigger rotary vane pump will work well. An exhaust mist filter is recommended
and a cold trap is a good idea.
COLD TRAP
1.5 Gallon Cold Trap (2QT Tank) Dry Ice, Liquid Nitrogen - GLASS LID
SKU: BVV15CT-G
1.5 Gallon (2QT Tank) Dry Ice, Liquid Nitrogen Cold Trap
$220
Other Equipment:
Meat thermometers
https://www.amazon.com/gp/product/B005KDDCAC/ref=ppx_yo_dt_b_asin_title_o04_s00?ie=
UTF8&psc=1
Boiling beads
uxcell 7mm Solid Round Clear Glass Ball Boiling Stones Soda Lime Glass Beads 100pcs
https://www.amazon.com/gp/product/B09CD7DCGW/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=
UTF8&psc=1
Tubing 90-degree splicer 3/8” to 3/8”
Buy Fittings Online 3/8 in. 90 Degree Elbow Barbed Splicers 304 Stainless
https://www.buyfittingsonline.com/stainless-steel-beverage-fittings-splicers-barbed-90-degreeelbows-tubing--bev-371/
Tubing Reducer 1/4" to 3/8”
Quickun Plastic Hose Barb Reducer Fitting 3/8" to 1/4" Barbed Reducing Union Adapter Splicer
Mender Joint Fitting ( Pack of 2 )
https://www.amazon.com/gp/product/B07YRRXJ4K/ref=ppx_yo_dt_b_asin_title_o08_s00?ie=U
TF8&psc=1
Tubing coupler 3/8” to 3/8”
Beduan Stainless Steel 3/8" Hose Barb Splicer Mender Round Union Coupler Fitting (Pack of 2)
https://www.amazon.com/Beduan-Stainless-Splicer-CouplerFitting/dp/B07P2DLBPC/ref=sr_1_19?crid=3497W03HG8XCC&keywords=3%2F8"+to+3
%2F8%22+tubing+coupler+stainless&qid=1652300226&sprefix=3%2F8+to+3%2F8+tubing+co
upler+stainless%2Caps%2C107&sr=8-19
Additional Equipment:
Butterfly hose clamps
Silicon mats
IR thermometer gunTeflon tape
Fire Extinguisher
Jars
shopBVV has the lids and other parts. The list will make sense once you read his articles or view the videos. You do not need everything on this list. He just gives choices.
Was hoping to just drop a pdf but site won’t let me.
6 Likes
Thank you!! Booked marked 
3 Likes
Thanks but i have my own “honey-do” list 
3 Likes
Thank you very much for posting the QWET instructions.
I decarbed about an ounce of Sticky Icky(gorilla glue #4 x Animal Cookies), Daiquiri, zeppoli and a few nice chunks of bubble hash.
Followed your updated directions… Evaporating now.
I stuck the handle of my strainer into the spout of our tea pot to hold it.
I did two coffee filters after the cheese cloth.
I forgot to take pics, but the outcome was super clear honey colored.
Didn’t care for the smell of the decarbed bud. The original bud was great and all great terps… But decarbed bud… Ick.
Have it evaporating like your instructions… In the basement.
Will check it tomorrow and the next day. And update with a pic or two.
Thank you once again! It was sooooo simple. Annnnd Everclear is cheap and easily to find here.
I hope you have a great weekend.
6 Likes
Coolio! Glad it’s working. Yes, don’t decarb the weed you are going to smoke it… also some don’t decarb the weed but wait until you evap all then decarb the concentrate.
5 Likes
Planning to use Everclear to wash de-carbed buds.
Pre-warmed Quart jar, half filled, canning lid ready for end of process sealing.
Then using titrate of THC/Grain Alcohol, make Kaluha for morning coffee addition.
Anybody ever Vacuum-extract all possible air from jars before oven routine?
That brings to mind the question of processing (curing weed) using vacuum extraction until 65%?
Still learning interesting techniques for enjoying my grow.
6 Likes
I’ve never even heard of vacuuming out the air from the jars. What is the reason for that?
3 Likes
Just asking, but no experience with it.
Today I cooked this 5oz from the fall harvest.
2-oz buds and 3 oz shake (kief mined shake).
Jars Vac sealed from oven cook, as should (pings heard and felt).
Rings sealed and in the freezer.
Saw some residue on inside moisture or oil?
Everclear from freezer went to Kaluha cook.
Another Everclear chilling for bud wash.
PNW weather today WET and raining.
Me inside, dry, and surprisingly productive.
Smoking the Kief and having Jerry’s coffee.
9 Likes
Are you leaving buds whole while you’re cooking it, or do you break it down?
2 Likes
Left these whole (two jars). The shake jar was kief mined.
Not sure best method for proceeding so any advice is appreciated.
I would crumble buds before washing and ultimately tea or brownies, or the Kahlua.
Probably Freezer to NINJA blender and filtering. No need to crumble, Thoughts?
3 Likes
My unit grinds the flower during its process
1 Like
Don’t grind it. Just break down by hand until large rice grain size (or a little more). This keeps the trichomes intact and it’s easier to strain.
3 Likes
Awseome… I could get a two-fer…
Give one to my wife and use it when she is not home. WIN-WIN
Thanks.
@Caligurl so you say, small, small nuggets. Got it, thank you.
4 Likes
Here I am sharing an interesting topic about "The Impact of Legalization on Medical Marijuana Businesses . Please take a look and let me know your point of view.
2 Likes
Welcome @Find420!
Just my 2 cents and mainly from what I see here in Cali (legal recreational).
All the regulations, taxes, license and permit fees, lab testing, etc… make it hard for the little guys to compete. Corners are cut and dispos are (knowingly AND unknowingly) purchase products that haven’t been inspected or passed lab tests and regulations. a LOT of studies have been done taking samples directly from dispos in every legal state and they are finding too many illegal pesticides and fungicides.
So pay more for ‘safe or organic’ products… if you can find them…or do what we do here and grow your own!!! At least you know whats in/on it!
I looked into starting an edibles ‘bakery/cafe’ and I had to be currently renting (or own) the property on which I want to apply for a permit for for at least 1 year. THEN, if I was granted the permit, had to wait another full year (at that location) to get the license (IF I even got the license)… that’s 2 full years of paying for a location that I may or may not be able to even get to operate on… For a SMALL space around here, you can pay around $10,000/month for a space… that $240,000 in an EMPTY space.
I thought about using that space, instead , for a growers/hydroponics store until then but that would take a lot of additional capital to stock it and then pay at least one staff person.
So now I know why people cut corners and dispos buy illegal pot. And I also know why I grow my own. I’ll just have to settle for making my own edibles and giving away (not selling) to others.
7 Likes
Thank you, so much.
I now feel better about all the pursuit of good weed.
Absolutely, a magical plan.
3 Likes